• Easy to apply.
• Excellent stain, acid, and scratch resistance.
• Excellent field repair-ability.
• No chance of catastrophic failure.

Easy, Predictable Results

Easy enough for a do-it-yourselfer to use and durable enough for commercial and industrial applications, the Trinic H-12 Sealer Kit will help you put a professional finishing touch on any concrete project. Use Trinic H-12 Sealer on countertops, furniture, floors, fireplace surrounds, sinks, and more to get a beautifully sealed surface.In this convenient sealer kit you will get both H-12 Sealer Side-A and H-12 Sealer Side-B as well as a 60ml and 10ml syringe for mixing.

When you use this two-component hybrid water-based sealer there is no chance of catastrophic failure. With the ability to deeply penetrate concrete surfaces, it’s easy to apply and just as easy to repair in the off chance of an accident. Trinic H-12 Sealer offers superior stain, acid, and scratch resistance so you know that your finished product will keep its flawless finish for many years to come.

• Clean mixing container.
• Two syringes for measuring small amounts (to avoid cross contamination).
• Clean potable water.
• High density foam roller.

• Combine 2 parts A to 1 part B mix for 1 minute minimum making sure all of the catalyst is thoroughly homogenized within the mixture.
• First Coat – Add 7 parts water to 1 part sealer.
• Second Coat – Mix 4 parts water to 1 sealer.
• Two coats may be adequate for low use areas such as fireplace surrounds.
• Third Coat (Option 1) – 2 parts water to 1 part sealer.
• Third Coat (Option 2) – 3 parts water to 1 part.
• Three coats may be adequate for vanities, a fourth is recommended for high abuse areas such as kitchen countertops.
• Fourth and final Coat – 2 parts water to 1 part sealer.

• Flood the surface with diluted H12.
• Roll with a high density foam roller.
• Keep wet for up to 5 minutes or until the concrete stops absorbing sealer.
• Keep rolling until all foam is gone and roller marks disappear, Ring out foam roller to remove any access material. The thinner the coat the better the scratch resistance.
• Remember – "Thin to Win."
• Once there are no longer roller lines or foam left on surface let sit until the coat is dry to the touch. When you can rub it with your finger and not leave a mark, its ready for the next coat. This generaly takes about an hour at 75 degrees, about 2 to 3 hours at 60 degrees.
• You can use 600 grit sandpaper to remove dust particles from the sealer after it has cured a couple of days, if you attempt to sand the sealer to early in the cure cycle you may end up removing it.

• The sealer will have excellent blush resistance in three days.
• The sealer requires seven days to have excellent scratch, acid, and stain protection.
• The sealer will continue to build hardness out to 14 days.

• Small scratches can be spot repaired by filling the scratch with sealer and wiping off excess.
• The sealer can be re-coated by sanding the tops with 200 to 400 grit sand paper and sealing with an additional coat of sealer.

• Trinic H-12 Sealer Part I
• Trinic H-12 Sealer Part II
• Trinic H 12 Tips and Techniques

• Easy to apply.
• Excellent stain, acid, and scratch resistance.
• Excellent field repair-ability.
• No chance of catastrophic failure.

Easy, Predictable Results

Easy enough for a do-it-yourselfer to use and durable enough for commercial and industrial applications, the Trinic H-12 Sealer Kit will help you put a professional finishing touch on any concrete project. Use Trinic H-12 Sealer on countertops, furniture, floors, fireplace surrounds, sinks, and more to get a beautifully sealed surface.In this convenient sealer kit you will get both H-12 Sealer Side-A and H-12 Sealer Side-B as well as a 60ml and 10ml syringe for mixing.

When you use this two-component hybrid water-based sealer there is no chance of catastrophic failure. With the ability to deeply penetrate concrete surfaces, it’s easy to apply and just as easy to repair in the off chance of an accident. Trinic H-12 Sealer offers superior stain, acid, and scratch resistance so you know that your finished product will keep its flawless finish for many years to come.

• Clean mixing container.
• Two syringes for measuring small amounts (to avoid cross contamination).
• Clean potable water.
• High density foam roller.

• Combine 2 parts A to 1 part B mix for 1 minute minimum making sure all of the catalyst is thoroughly homogenized within the mixture.
• First Coat – Add 7 parts water to 1 part sealer.
• Second Coat – Mix 4 parts water to 1 sealer.
• Two coats may be adequate for low use areas such as fireplace surrounds.
• Third Coat (Option 1) – 2 parts water to 1 part sealer.
• Third Coat (Option 2) – 3 parts water to 1 part.
• Three coats may be adequate for vanities, a fourth is recommended for high abuse areas such as kitchen countertops.
• Fourth and final Coat – 2 parts water to 1 part sealer.

• Flood the surface with diluted H12.
• Roll with a high density foam roller.
• Keep wet for up to 5 minutes or until the concrete stops absorbing sealer.
• Keep rolling until all foam is gone and roller marks disappear, Ring out foam roller to remove any access material. The thinner the coat the better the scratch resistance.
• Remember – "Thin to Win."
• Once there are no longer roller lines or foam left on surface let sit until the coat is dry to the touch. When you can rub it with your finger and not leave a mark, its ready for the next coat. This generaly takes about an hour at 75 degrees, about 2 to 3 hours at 60 degrees.
• You can use 600 grit sandpaper to remove dust particles from the sealer after it has cured a couple of days, if you attempt to sand the sealer to early in the cure cycle you may end up removing it.

• The sealer will have excellent blush resistance in three days.
• The sealer requires seven days to have excellent scratch, acid, and stain protection.
• The sealer will continue to build hardness out to 14 days.

• Small scratches can be spot repaired by filling the scratch with sealer and wiping off excess.
• The sealer can be re-coated by sanding the tops with 200 to 400 grit sand paper and sealing with an additional coat of sealer.

• Trinic H-12 Sealer Part I
• Trinic H-12 Sealer Part II
• Trinic H 12 Tips and Techniques